Woodworking band saw is a good tool for wood turners and wood workers for several reasons.
Like all woodworking machinery and equipment, it is important that the wood band saw machine be set up correctly, and regularly tuned and checked for band saw safety rules. Refer to your band saw guides for this.

Home wood shops typically include two wheel saws of fourteen inches in diameter. This measurement refers to the diameter of the wheels, and not the diameter of the cut, which is usually six inches.
These wheels resemble typical bicycle tires with rims and tires.

Though it will be new when a new saw is purchased, over time, through usage, the tires have to be brushed to remove accumulated dust which tends to stick to them. Green softwoods are notorious for this. The wheels also have to be lined up correctly.

They are lined up correctly when they are parallel to each other and are running coplanar. There should be a way in which the distance of the free running wheel is adjusted. This is the wheel that is not connected to the motor. This can be done in many ways, so you should consult the saw’s instruction manual to find out how.

For the wheels to be parallel and coplanar, there has to be a straight edge across both wheels, put directly in front of the axles, and they should touch the all sides of the rims, of both wheels, at the same time.

After this is achieved,band saw blades for wood should be positioned at the center of both of the wheels. There is an adjustment knob to enable this. Make sure that the wood band saw is unplugged, then turn the wheels by hand and adjust to track in the center.

You have to tighten the band saw blades for wood in order for it to be moved by a quarter of one inch. Or you can follow the instructions contained in the saw’s manual. Every blade has to be tightened and tracked when it is installed, and will need regular adjustments.

Band saw machines are ideal for wood preparation for small and big projects alike. For smaller projects, you can create cuts of one quarter inches using a six tooth band saw blade. You can even get a mini aka small band saw.

It can also be used to cut pieces of wood several inches thick. Heavy wood, like green wood, will need a 3/8 three point blade, or similar.

Like all other types of saws, blades’ have to be cleaned and their sharpness has to be maintained for them to continue working properly.

Wood Band Saw machines are excellent for straight or curved wood cutting. They are essential tools to have for any wood worker. They are easy to use, and are one of the safest tools to use.

Beside Blade material you should pay attention to a few more things when buying new Bandsaw blade:
1. Blade Length – Simply measure the length of the blade needed.
2. Blade Width – It is important to use the correct width of the blade (recommended by the manufacturer) for your band saw. Usually you can use smaller width but under no circumstance you should go wider. A wide blade gives you more stability and a straighter cut. Narrower blade gives you tighter radius. In principle, the wider the Band Saw blade, the higher its beam strength and the better it can maintain straightness.
3. Blade Thickness – You should try to stay with the same thickness to avoid having to make adjustments when changing blades, because some blades of the same width come in different thickness. If you need to adjust your saw to different thickness follow the instructions for adjusting.

4. Pitch or Teeth Per Inch – To determine the number of teeth per inch, measure one inch of the blade from gullet to gullet and count the number of full teeth between them. This only works on constant pitches. Blades with more TPI (teeth per inch) will make a smoother cut but the blade will cut slower, a blade with fewer TPI will cut quicker but it will leave a rougher finish. For example for resawing, you need an aggressive blade, ( few TPI and as wide as the saw will accommodate).

The general rule is to have at least 3 teeth in the material at all times and run as wide a blade as possible for the particular job.

To prolong the life of your Band Saw blades and to stop them from wondering while cutting you should pay attention to the tension, and follow the instructions. According to many woodworkers it’s always better to add a bit more tension than indicated.

If you use your Band Saw to cut metal, you need a good cutting fluid for almost all materials. Cast iron should be cut dry and aluminum should be cut with power paraffin. You can choose between water soluble fluids or a neat cutting fluids.

Tooth forms in Band Saw blades are:

Raker tooth (S) – available in constant tooth pitches of 3-32 tpi blades and in the variable tooth pitch blades of 3-4 tpi to 10-14 tpi. Blades with this tooth form are suitable for short clipping materials (steel or cast iron) and small cross sections.

Hook tooth (K) – on blades with constant tooth pitches of 0.75-6 tpi and in blades with variable tooth pitches of 0.55-0.75 tpi to 4-6 tpi. Blades with this tooth form are suitable for long chipping tough materials, non ferrous metals and steels with a carbon content smaller than 0.8%, strong structural, rust resistant steels, acid resistant steels and large cross sections

Skip tooth (L) – on blades with constant tooth pitches of 2, 3, 4 and 6 tpi. Blades with this tooth form are suitable for fragile or brittle materials and large cross sections.

Trapezoidal tooth (T) – on blades with variable tooth pitches of 0.85-1.15 tpi to 3-4 tpi. Blades with this tooth form are suitable for high band sawing demands.